FW : sas2xfwYYMMDD.fw Command to update, 1)"fdl code 0" to update new fw file 2)"reset" MFG data : mfgdat6gMMDD.rom Command to update, 1)"fdl mfgb 0" to update new data file 2)"reset" after boot, cmd > rev ================================================================================ Hardware Revision Information:- ================================================================================ Vendor ID :Areca Product ID :6G-Expander Product Revision Level :Minor = 0x03, Unit = 0x11 Component ID :0x0223 (Bond Option :36) Component Revision Level :4 (B2) Customer Code :0x1 or 0x3F or 0x1A Manufacturer Data Revision :0xB6 ================================================================================ Firmware Revision Information:- ================================================================================ Active Firmware: Active Image Boot Image: Revision: 255.3.5.10 Fast Boot: No Image Address: 0x14000000 Active Image: Revision: 255.3.17.0 Fast Boot: No Image Address: 0x14080000 Backup Image: Revision: 255.3.17.0 Fast Boot: No Image Address: 0x14100000 Change logs -------------------- 2010/09/23 Released For Chip rev: B3 Revision: 7.01.03.82 09/23/10 Firmware Family: 1 A)Fix when device temperature OVT warning flag is not set when temperature great than a critical limit. 2010/09/27 A)update the code to configure SdMegaWrapper register. 2010/10/13 A)Update to fill the SES speed code as 0. B)Fix when device temperature OVT warning flag is not set when temperature great than a critical limit. C)Fix CLI shell been logout during keyin command string. D)Update drivenstrength command parameters usage. 2010/10/14 Released For Chip rev: B3 Revision: 7.01.05.88 10/14/10 Firmware Family: 1 A)Update "fdl" command default offset is 0, if no offset value input. B)Fix LCM password verify fail if password length equal to 8. 2010/11/03 Released For Chip rev: B3 Revision: 7.01.06.8D 11/03/10 Firmware Family: 1 A)Modify code which reduce the time that device ID 0x0E use to get sensor status. B)Code to protect GAL watch dog timeout during FW copy at the BOOT stage. C)Disable ARC-8026 expander GPIO heart-beat function. 2010/12/08 Released For Chip rev: B3 Revision: 7.01.07.90 12/08/10 Firmware Family: 1 A)Support HDD access led on some model. (H/W GAL support) 2011/01/12 Released For Chip rev: B3 Revision: 7.01.08.93 01/12/11 Firmware Family: 1 A)Update fan speed up before OVT warning function. B)Fix the ARC-8026 LCM Fan/Power string shown when the device are not install. C)Fix the ARC-8026 PWR fail label text mismatch with CLI. 2011/02/11 Released For Chip rev: B3 Revision: 7.01.09.96 02/11/11 Firmware Family: 1 A)Support Redundant JBODs. B)Fix Areca PSU I2C retry issue. C)ARC-8026 suppor very low rpm fan. 2011/05/18 Released v1.10 For Chip rev: B3 Revision: 7.01.10.9B 05/18/11 Firmware Family: 1 A)When ARC8026 PWR sensor is disabled, clear some SES common status bit. B)Fix the temperature element detect OVT fail at some condition. C)Fix when set Auto Fan, the backup expander fan speed code is not match with master. 2011/05/25 Released v1.11 For Chip rev: B3 Revision: 7.01.11.9D 05/25/11 Firmware Family: 1 A)Fix bug that can't disable PHY correctly. B)Fix Data file not found when upgrade FW from Revision: 7.01.09.96 02/11/11. C)Fix SES page 02 critical bit set always. 2011/08/08 Released For Chip rev: B3 Revision: 7.01.12.A3 08/08/11 Firmware Family: 1 A)Limit the high warning & low warning temp/ setting less than 100'c. B)Fix expander always set fan at level 1 when auto fan is enabled on some models. C)Support cli command "sys" to show GAL revision. D)Add a protect on MFG data copy to prevent from watchdog timout. E)Fix device ID 0x06 no fan installed issue. 2011/10/05 Released For Chip rev: B3 Revision: 7.01.13.A9 10/06/11 Firmware Family: 1 A)Fix the group function. B)Fix for ARC-1880 series "Request for Empty Slot" function. C)Fix the empty slot led function conflict with LSI 6G RAID adapter. use "sys -y [on|off]" to enable/disable the function of empty slot led. default is off. D)Fix the issue that make LSI MSM (Megaraid storage) can't log messages. E)Enlarge the IO delay after switch the fan group make read fan speed more preciselly. F)Fix the bug that after manually change the fan speed, all of the sensors will report wrong status. For standalone expander ARC-8016, ARC-8026 only. 2011/12/28 Released For Chip rev: B3 Revision: 7.01.14.AB 12/28/11 Firmware Family: 1 A)Add more protection for MFG data file. B)Support device ID 0x08, 0x88, Rev. 0x01. C)Support device ID 0x43,0x44,0x45, Rev. 0x01. 2013/03/05 A)Support device ID 0x08, 0x88, Rev. 0x01. B)Support ARC-8068 12/16/24 bays 2013/03/07 Released For Chip rev: B3 Revision: 14.01.15.09 03/07/13 A)Migrate to new SDK kernel. 2013/12/25 Released For Chip rev: B3 Revision: 14.01.16.0B 12/25/13 Firmware Family: 1 A)Support ARC-4036 connnector 2/3 drive mode. B)Support ARC8026 & ARC4036 auto fan mode